Sealing Up Patient Safety with Monte Carlo Simulation

Sealing Up Patient Safety with Monte Carlo Simulation

By Discovery Lean Six Sigma

0/5 stars (0 votes)

Sealing Up Patient Safety with Monte Carlo Simulation

If you have a process that isn’t meeting specifications, using the Monte Carlo simulation and optimization tools in Companion by Minitab can help. Here’s how you, as an engineer in the medical device industry, could use Companion to improve a packaging process and help ensure patient safety.

Your product line at AlphaGamma Medical Devices is shipped in heat-sealed packages with a minimum seal strength requirement of 13.5 Newtons per square millimeter (N/mm2). Meeting this specification is critical, because when a seal fails the product inside is no longer sterile and puts patients at risk.

Seal strength depends on the temperature of the sealing device and the sealing time. The relationship between the two factors is expressed by the model:

Seal Strength= 9.64 + 0.003*Temp + 4.0021*Time + 0.000145 Temp*Time

Currently, your packages are sealed at an average temperature of 120 degrees Celsius, with a standard deviation of 25.34. The mean sealing time is 1.5 seconds, with a standard deviation of 0.5. Both parameters follow a normal distribution.

Building your process model

To assess the process capability under the current conditions, you can enter the parameter, transfer function, and specification limits into Companion’s straightforward interface, verify that the model diagram matches your process, and then instantly simulate 50,000 package seals using your current input conditions.

seal strength model monte carlo simulation Understanding your results monte carlo output for seal strength simulation round 1

The process performance measurement (Cpk) for your process is 0.42, far less than the minimum standard of 1.33. Under the current conditions, more than 10% of your seals will fail to meet specification.

Finding optimal input settings

Companion’s intuitive workflow guides you to the next step: optimizing your inputs.

parameter optimzation

You set the goal—in this case, minimizing the percent out of spec—and enter high and low values for your inputs. Companion does the rest.

defining optimization objectives Simulating the new process

After finding the optimal input settings in the ranges you specified, Companion presents the simulated results of the recommended process changes.

second seal strength model monte carlo simulation

The simulation shows the new settings would reduce the amount of faulty seals to less than 1% with a Ppk of 0.78—an improvement, but still shy of the 1.33 Ppk standard.

Understanding variability

To further improve the package sealing process, Companion then suggests that you perform a sensitivity analysis.

sensitivity analysis

Companion’s unique graphic presentation of the sensitivity analysis provides you with insight into how the variation of your inputs influences seal strength.

sensitivity analysis results

The blue line representing time indicates that this input’s variability has more of an impact on percent of spec than temperature. The blue line also indicates how much of an impact you can expect to see: in this case, reducing the variability in time by 50% will reduce the percent out of spec to about 0 percent. Based on these results, you run another simulation to visualize the strength of your seals using the 50% variation reduction in time.

third monte carlo model simulation for seal strength

The simulation shows that reducing the variability will result in a Ppk of 1.55, with 0% of your seals out of spec, and you’ve just helped AlphaGamma Medical Devices bolster its reputation for excellent quality.

Getting great results

Figuring out how to improve a process is easier when you have the right tool to do it. With Monte Carlo simulation to assess process capability, Parameter Optimization to identify optimal settings, and Sensitivity Analysis to pinpoint exactly where to reduce variation,  Companion can help you get there.

To try the Monte Carlo simulation tool, as well as Companion's more than 100 other tools for executing and reporting quality projects, learn more and get the free 30-day trial version for you and your team at companionbyminitab,com.





Original: http://blog.minitab.com/blog/understanding-statistics/sealing-up-patient-safety-with-monte-carlo-simulation
By: Eston Martz
Posted: July 14, 2017, 12:00 pm

comments powered by Disqus

Discovery Lean Six Sigma

Dummy user for scooping articles

I'm a dummy user created for scooping  great articles in the network for the community.