Dear Community Members

soon many contents will be available only for

**registered members**, please start to make the registration ( Register here ) for keeping updated with all future contents, it's free.Regards

- Blogs
- Discovery Lean Six Sigma
- Methods and Formulas: How Are I-MR Chart Control Limits Calculated?

Users often contact Minitab technical support to ask how the software calculates the control limits on control charts.

A frequently asked question is how the control limits are calculated on an I-MR Chart or Individuals Chart. If Minitab plots the upper and lower control limits (UCL and LCL) three standard deviations above and below the mean, why are the limits plotted at values other than 3 times the standard deviation that I get using **Stat > Basic Statistics**?

That’s a valid question—if we’re plotting individual points on the I-Chart, it doesn’t seem unreasonable to try to calculate a simple standard deviation of the data points, multiply by 3 and expect the UCL and LCL to be the data mean plus or minus 3 standard deviations. This can be especially confusing because the Mean line on the Individuals chart IS the mean of the data!

However, the standard deviation that Minitab Statistical Software uses is not the simple standard deviation of the data. The default method that Minitab uses (and an option to change the method) is available by clicking the I-MR Options button, and then choosing the Estimate tab:

There we can see that Minitab is using the **Average moving range** method with **2** as the **length of moving range** to estimate the standard deviation.

That’s all well and good, but exactly what the heck is an average moving range with length 2?!

Minitab’s **Methods and Formulas** section details the formulas used for these calculations. In fact, Methods and formulas provides information on formulas used for all the calculations available through the dialog boxes: This information can be accessed via the Help menu, by choosing **Help** > **Methods and Formulas...**

Too see the formulas for control chart calculations, we choose **Control Charts** > **Variables Charts for Individuals** as shown below:

The next page shows the formulas organized by topic. By selecting the link **Methods for estimating standard deviation** we find the formula for the **Average moving range**:

Looking at the formula, things become a bit clearer—the ‘length of the moving range’ is the number of data points used when we calculate the moving range (i.e., the difference from point 1 to point 2, 2 to 3, and so forth).

If we want to hand-calculate the control limits for a dataset, we can do that with a little help from Minitab!

The dataset I’ve used for this example is available HERE.

First, we’ll need to get the values of the moving ranges. We’ll use the calculator by navigating to **Calc** > **Calculator; **in the example below, we’re storing the results in column C2 (an empty column) and we’re using the **LAG** function in the calculator. That will move each of our values in column C1 down by 1 row. Click **OK** to store the results in the worksheet.

Note: By choosing the **Assign as a formula** option at the bottom of the calculator, we can add a formula to column C2 which we can easily go back and edit if a mistake was made.

Now with the lags stored in C2, we use the calculator again: **Calc** > **Calculator** (here's a tip: press F3 on the keyboard to clear out the previous calculator entry), then subtract column C2 from column C1 as shown below, storing the results in C3. We use the **ABS** calculator command to get the absolute differences of each row:

Next we calculate the sum of the absolute value of the moving ranges by using **Calc** > **Calculator** once again. We’ll store the sum in the next empty column, C4:

The value of this sum represents the numerator in the Rbar calculation:

To complete the Rbar calculation, we use the information from Methods and Formulas to come up with the denominator; n is the number of data points (in this example it’s 100), w’s default value is 2 ,and we add 1, so the denominator is **100-2+1**. In Minitab, we can once again use **Calc** > **Calculator **to store the results in C5:

With Rbar calculated, we find the value of the unbiasing constant d2 from the table that is linked in Methods and Formulas:

For a moving-range of length 2, the d2 value is 1.128, so we enter 1.128 in the first row in column C6, and use the calculator one more time to divide Rbar by d2 to get the standard deviation, which works out to be 2.02549:

We can check our results by using the original data to create an I-MR chart. We enter the **data** column in **Variables**, and then click **I-MR Options** and choose the **Storage** tab; here we can tell Minitab to store the standard deviation in the worksheet when we create the chart:

The stored standard deviation is shown in the new column titled STDE1, and it matched the value we hand-calculated. Notice also that the Rbar we calculated is the average of the moving ranges on the Moving-Range chart. Beautiful!

Original: http://blog.minitab.com/blog/marilyn-wheatleys-blog/methods-and-formulas3a-how-are-i-mr-chart-control-limits-calculated

By: Marilyn Wheatley

Posted: May 18, 2017, 3:07 pm

Dummy user for scooping articles

I'm a dummy user created for scooping great articles in the network for the community.

- January 2018
- December 2017
- November 2017
- October 2017
- September 2017
- August 2017
- July 2017
- June 2017
- May 2017
- April 2017
- March 2017
- February 2017
- January 2017
- December 2016
- November 2016
- October 2016
- September 2016
- August 2016
- July 2016
- June 2016
- May 2016
- April 2016
- March 2016
- February 2016
- January 2016
- December 2015
- November 2015
- October 2015
- September 2015
- August 2015
- July 2015
- June 2015
- May 2015
- April 2015
- March 2015
- February 2015
- January 2015
- December 2014
- November 2014
- October 2014
- August 2014
- July 2014
- June 2014
- April 2014
- March 2014
- February 2014
- January 2014
- December 2013
- November 2013
- October 2013
- September 2013
- August 2013
- July 2013
- June 2013
- May 2013
- April 2013
- March 2013
- February 2013
- January 2013
- November 2012
- October 2012
- September 2012
- August 2012
- July 2012
- June 2012
- May 2012
- March 2012
- February 2012
- November 2011
- October 2011
- September 2011
- August 2011
- July 2011
- June 2011
- May 2011
- April 2011
- February 2011
- January 2011
- December 2010
- November 2010
- October 2010
- September 2010
- August 2010
- July 2010
- June 2010
- April 2010
- March 2010
- February 2010
- December 2009
- November 2009
- August 2009
- June 2009
- March 2009
- November 2008
- October 2008
- July 2008
- May 2008
- April 2008
- March 2008
- February 2008
- June 2007
- February 2007
- August 2005

innovation, Articles, big data, Leadership, data management, Data Education, Blogartikel, Education Resources For Use & Management of Data, innovation excellence, & Education, Data Daily | Data News, lean manufacturing, lean, Quality Insider Article, Twitter Ed, Six Sigma, systems thinking, lean six sigma, Digitalisierung, Business, Big Data News, Management Article, Smart Data News, Management, Lean Management, strategy, The Latest, kaizen, Gastbeiträge, Problem solving, continuous improvement, Soft Skills, Interviews, Operations Article, Change, Uncategorized, marketing, statistics, systems view of the world, Organization, Theory of Constraints, Immobilien, Personal, Culture, technology, Videos, Banken, Sekretariat & Assistenz, quality, Project management